产品品牌:JAPAN:WM88
产品型号:WM-88
螺杆清洗剂型号:WM—88用途适用于清洗各类注塑成型、挤压成型及吹塑成型的螺杆和炮筒特性具有热安定性,性质温和不损害螺杆和炮筒可直接喷射料斗或混合塑料使用大大节省清洗用料量,降低成本大大缩短转色时间,提高生产效率使用简单方便快捷 环保配方,使用后不影响生产使用方法使用前把炮筒原残留的塑料全部射出,并清洁料斗,一公斤塑料配4克WM-88(约喷射三次)均匀混合后,放进料斗,按较高温料温度调整原则(比待转色塑料的加工温度高5-10℃)或咨询我司工程师。溶胶后,射出三次,等后2-3分钟后再射出3次,重复操作直到射完,完成炮筒清洁后,再加入1公斤(视乎机器大小而定)待生产的塑料,清洗积存螺杆上的清洗料,并清洗料斗注意事项使用前请戴工业手套,如沾及皮肤,立即用清水冲洗;如不慎溅入眼睛,立即用大量清水冲洗避免存放于阳光直射处或暴露于超过50℃的环境中不可吞食,避免儿童触及500ml/支 12支/箱Screw rod cleansing agent model: WM-88 use is suitable in cleans each kind of injection molding, the extrusion forming and the blow molding formation screw rod and artillery tube characteristic has the heat-resistant quality, the nature temperate does not harm the screw rod and artillery tube may the direct injection hopper or the mix plastic uses to save the clean to use greatly to estimate that reduces cost the big reduction annealing time, enhances production efficiency uses simple convenience quickly the environmental protection formula, before after the use, does not affect produces application method the use, the artillery tube original residual plastic to project completely, and the clean hopper, a kilogram plastic matchesafter 4 gram WM-88 (approximately sprays three times) the uniform mixing, admits the hopper, according to compares the high temperature material temperature adjustment principle (compared to treat annealing plastic processing temperature high 5-10℃) or consults my Engineer Si. After the sol, projects three times, and so on latter 2-3 minutes later projects again 3 times, the redundant operation until shoots, after completing the artillery tube cleanly, then joins 1 kilogram (to regard machine size to decide) treats the production the plastic, on the clean accumulation screw rod"s clean material, before and cleans hopper matters needing attention the use, please to wear the industry glove, like moistens and the skin, uses the clear water to flush immediately; If splashes carelessly into the eye, uses the massive clear water to flush immediately to avoid depositing or exposes in the sunlight perpendicular incidence place in surpasses 50℃ in the environment cannot swallow, avoids the child touching 500ml/ 12/box of专业批发销售:批发各种品牌脱模剂/顶针油/洗模水/防锈剂/WD-40/WO-60/金牛油/洗手粉/水塔清洗剂/螺杆清洗剂(又称注塑机炮筒清洗剂)。联系人:谢先生:15989411130 FAX:61182553 QQ:516018082 E-mail:xiexinjie168@126.com 欢迎光临本站 来电 来涵 订购 洽谈合作!全国各地含运费送到各地区域!‘塑’一流产品 ‘胶’天下朋友